ATIKA BKS 38 Instructions d'exploitation télécharger pdf (Page 23)

Check

B befo

B af

B during sawing regularly all 10 minutes

d saw chain and a sufficient

influence the durability.

B in temperature it

expands and needs to be reclamped.

the saw chain tension:

re start of work

ter the first steps

 Only with a correct clampe

lubrication you can

L Please observe the following:

B a new saw chain must be rest retched more frequently.

case of heating of chain to operating

After finishing the sawing works release tension of saw

erge

B guide clamp it again

chain as in case of cooling too high tensions would em

in the saw chain.

if chain flackers or comes out of the

immediately.

L aw is supplied without saw chain oil and

fuel filling.

Fill the saw ation" and

uelling".

The chain s

chain as described under "Chain lubric

Chain lubrication

operate the chain saw without lubrication. Any

se without chain saw oil may result in damage of the

power of the chain depends on the

autom

L Never

chain saw and guide bar.

The durability and cutting

optimal lubrication. During operation the saw chain is

atically wetted with oil.

Filling up saw chain oil

Stop the engine and wear protective

gloves.

Avoid eye and skin contact.

Put the chain saw on a suitable base and unscrew the oil

C Fill the oil tank with bio-degradable chain saw

dhering oil r filling use a

tank lock 1).

a (order no. 400144). For easie

funnel.

When filling observe that no dirt reaches the oil tank.

 N

when using oil which is not allowed for chain saws.

Screw on the oil tank lock again.

ever use recycled oil or used oil. The guarantee expires

Checking the chain lubrication

chain

brication.

chain lubrication by

on the chain saw and holding it with the pike in

Never operate the chain saw without functioning

Check the function of the automatic

switching

direction of a carton or paper on the ground.

Do not get in contact with the ground with the chain. Keep a

ck despite full oil

safe distance of 20 cm.

If an increasing oil track is caused when checking it the oil

automatic works faultless. If there is no oil tra

tank:

Clean the oil flow channel (19).

If this is not s

B uccessful please contact the customer

service.

Adjust the chain lubrication:

 See also the instructions under "Maintenance /

cleaning: Adjusting the chain lubrication".

andling fuel

open flames

(risk of explosion).

Utmost care is required when h

and oil. Do not smoke. Keep away

This product is operated by a mixture from regular

Petrol: ct

Do not fill in leaded petrol,

fuels.

 Do t than 91

s due to

 oil for air-cooled engines.

petrol (unleaded) and two-stroke engine oil.

ane number at least 91 ROZ unleaded O

 diesel or other non-approved

use petrol having a smaller octance number

ROZ. This may lead to severe engine damage

increased engine temperatures.

 If you frequently operate the product at high speeds, you

should

use petrol with a higher octane number.

CThe use of unleaded petrol is recommended for envi-

ronment protection reasons.

o-stroke engine oil:

acc. to JASO FC or ISO EGD specifications

Do only use two-stroke engine

Ratio of mixture 40:1

Petrol Two-stroke engine oil

1 litre 0,025 litres

2 litres 0,050 litres

5 litres 0,125 litres

10 litres 0,250 litres

 sure the oil quantity accu mall deviation of it

large effect on the ratio of mixture in particular for

fuel quantities.

 change the ratio of m will lead to more

Mea rately as a s

has a

small

Do not ixture. This

residues of combustion, a higher fuel consumption, a

decrease of output or damages to the engine.

Mix petrol and oil in the supplied fuel mixing can (38).

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 134 135

Commentaires sur ces manuels

Pas de commentaire

ATIKA BKS 38 Instructions d'exploitation Page 23

Commentaires sur ces manuels